This is the second post in a series of blogs about how to configure and deploy a bare metal controller using Ironic. The first post described the requirements needed to accomplish this deployment.
In order to use a server as an Ironic node, first configure some BIOS parameters. Check the motherboard manual to determine how to access the BIOS panel, usually by pressing the button F2 or F10. The following images are for illustrative purpose only. Not all BIOS have the same layout so the next step is to find how to configure the following parameters in the motherboard’s BIOS.
First, setup the server to stay down after a power failure. Ironic will bring it up if needed.
Image 1: sample server management configuration
In the configuration panel, go to the NIC configuration menu and disable Preboot eXecution Environment (PXE) in all interfaces except the one which is going to be connected to the Ironic network. In this case, we are using the same network interface for Intelligent Platform Management Interface (IPMI) management and PXE booting , but the administrator can install a second interface to be used for PXE. It is recommended to use the fastest interface for PXE to speed up the download of the operating system images.
Image 2: NIC configuration
Once PXE has been configured for one network interface, go to boot options and set as first option PXE.
Image 3: boot options
Finally, save the changes and exit.
Image 4: exit and save changes
The following configuration option is very useful for debugging purposes. In the console redirection menu, set the redirecting server’s console to a serial (COM) port. With that done, it can be accessed via IPMI to remotely see, for example, the server screen during the boot process.
Image 5: console redirection
At this point, two different scenarios are possible: to have an operating system or not to have an operating system in the node server. Of course it is easier to have an operating system, but not necessary.
Before modifying any parameter it is important to be familiar with the IPMI environment. IPMI uses a channel model for direct communications between a communications interface and the Baseband Management Controller (BMC). Each channel has its own properties and its own configuration .
Before continuing, it’s very important to know which IPMI channel is assigned to the network interface. To find out, first configure all the IPMI network interfaces with different IP addresses. Next, ping them. Because of the direct connection to only one network interface, only one will reply.
The next step varies depending on whether an OS is installed.
No operating system: access the BIOS again and configure the basic IPMI parameters:
The IPMI IP address and force it to be static.
Enable the root user and set a password.
Enable the access to this channel.
With an operating system: install the IPMI tool:
apt-get get install ipmitool
Next, configure the same parameters described above but using this command line tool:
ipmitool lan set <channel> ipsrc static ipmitool lan set <channel> ipaddr <IPMI IP address> ipmitool lan set <channel> netmask <IPMI netmask> ipmitool lan set <channel> arp respond on ipmitool lan set <channel> auth ADMIN MD5 ipmitool lan set <channel> access on # Enable root user (user ID = 2) ipmitool user enable 2 # Set root password ipmitool user set password 2 <password>
Check all parameters by executing this command:
ipmitool lan print <channel>
Change the server name by changing the system info:
ipmitool mc setsysinfo system_name <server name>
Once this configuration is finished, try to access the node server from the controller server using the ipmitool to retrieve the chassis status:
ipmitool -I lanplus -H <IPMI IP address> -U root -P <password> chassis status
Additional instructions on how to implement the next steps will be provided in follow-on blogs.
 Preboot Execution Environment (https://en.wikipedia.org/wiki/Preboot_Execution_Environment)
 Thomas Krenn Wiki (https://www.thomas-krenn.com/en/wiki/IPMI_Basics)
Intel's compilers may or may not optimize to the same degree for non-Intel microprocessors for optimizations that are not unique to Intel microprocessors. These optimizations include SSE2, SSE3, and SSSE3 instruction sets and other optimizations. Intel does not guarantee the availability, functionality, or effectiveness of any optimization on microprocessors not manufactured by Intel. Microprocessor-dependent optimizations in this product are intended for use with Intel microprocessors. Certain optimizations not specific to Intel microarchitecture are reserved for Intel microprocessors. Please refer to the applicable product User and Reference Guides for more information regarding the specific instruction sets covered by this notice.
Notice revision #20110804