面向英特尔® 凌动™ 处理器的 Intel® Embedded Software Development Tool Suite

ERROR E-2201: The DAL interface library was loaded but the call to AllocIUmanaged failed

Hello!

I've got an error in Intel JTAG Debugger 2014 when trying to connect to ITP-XDP3 - ERROR E-2201: The DAL interface library was loaded but the call to AllocIUmanaged failed.

How can I solve this problem?

Thanks in advance!

 

BLDK for E5-2600v2 Family and S2600CP

Hello

I was referred to these forums by Intel support to verify that the Boot Loader Development Kit (BLDK) could be used for an Intel Xeon E5-2680v2 CPU being run on an Intel S2600CP4 Server board now or in the future. They seemed to believe so but could not confirm this and recommended I try here. Does anyone have any feedback on this? What documentation I could find on the BLDK mentioned only a few supported products.

Thank you!

Whether is there plan for ISS for Android on Mac OS X host?

Hi,

Whether is there any plan for ISS for Android on Mac OS X host, especially VTune Amplifier for Android? Because currently, almost all Android developers are working for Android and iOS at same time, and they are using Mac OS X as host, whether should we engage them to use ISS as their familiar environments?

Thanks a lot!

Y.Y.

Error Message: "adb - device not found" in Intel® VTune™ Amplifier 2014 for Systems

When trying to Create a New Analysis in Intel® VTune™ Amplifier 2014 for Systems to connect to an Android* Device.

You may get the error message:

adb - device not found

cannot communicate with the target.

Error while getting collector context values.

or in Project Properties you might get the error message:

There are no Android Devices attached to this machine.  You will not be able to collect any data.

There are 3 potential reasons for this:

  • 开发人员
  • 英特尔 AppUp® 开发人员
  • 合作伙伴
  • 教授
  • 学生
  • 安卓*
  • Android*
  • C/C++
  • Java*
  • 高级
  • 入门级
  • 中级
  • 安卓* 开发工具
  • 英特尔® VTune™ 放大器
  • 面向英特尔® 凌动™ 处理器的 Intel® Embedded Software Development Tool Suite
  • 英特尔® System Studio
  • 英特尔® VTune™ 放大器 XE
  • 开发工具
  • 英特尔® 凌动™ 处理器
  • 英特尔® 酷睿™ 处理器
  • 移动性
  • 优化
  • yocto project tachyon_inspxe example

    1)  Following the instructions in the document "How to use Intel Inspector 2013 for Systems", to set up and run the tachyon thread analysis example. In the Cross compiling section, it states to modify the make files. For the top-level Makefile, states to remove the line containing CXX. This appears to leave the Makefile with no spec of compiler (CXX = gcc originally). This doesn't seem correct, or is it???

    System Studio 2013 build error, for Inspector static-analysis

    Have a project originally built with gcc/gnu tools, targeting Atom 6xx series.

    Now importing to System Studio 2013.

    Existing make files were edited to switch over to icc. All compiled ok.

    Then added static analyzer (for Inspector) via CFLAGS, as,

      -diag-enable sc-precise

    to each of the corresponding sub-module make files.

    This resulted in following error during build, for one sub-module (called SMBus):

    订阅 面向英特尔® 凌动™ 处理器的 Intel® Embedded Software Development Tool Suite